Skip to content

Black Friday

25% off every projector screen

Ends in

Shop the sale

Black Friday sale: 25% off every projector screen, ending 30 November.

Shop now

Smarthome

Relay vs IR Control for a Motorised Screen: Which to Choose

November 13, 2026

A motorised screen is only as convenient as the thing that tells it to move. You can have a beautifully installed 120″ electric screen in a converted loft, but if the trigger is unreliable, every film night starts with a hunt for the remote. That is the practical problem behind the relay versus IR question — not which technology sounds more advanced, but which one you can trust when the lights are low and the room is full.

This guide is for anyone wiring an electric projector screen into a smart home setup, a dedicated cinema room, or a meeting space where the screen should drop without fuss. We will compare dry-contact relay triggers, infrared control, and app-based automation, then look at wiring practicalities and which ABIS electric screen suits each approach.

Key takeaways

  • Relay (dry contact) control is the most dependable for fixed installations because it uses a physical switch closure — no line of sight, no pairing, no app required.
  • IR is simple and wireless but needs a clear path to the screen’s receiver and can be fiddly in bright rooms or behind furniture.
  • App and voice control add convenience, but they usually sit on top of a relay or IR module rather than replacing it.
  • Most electric screens use a three-wire trigger (up, down, common) — check the screen’s control input before buying a smart relay.
  • For a room where the screen must disappear, electric with a relay trigger is the cleanest long-term choice; manual pull-down remains the budget option where power is difficult.

What relay control actually does

A relay trigger is about as basic as automation gets: two wires touch, the screen moves. In practice, a dry-contact relay module — often inside a smart home controller, a projector with a 12V trigger output, or a dedicated wall switch — closes a circuit that the screen interprets as “up” or “down”. There is no wireless protocol to drop, no remote to lose, and no line of sight needed.

That matters in UK rooms where the screen may be recessed into a ceiling bulkhead or mounted above a bay window. Once the screen is boxed in, IR is often blocked. A relay keeps working because it is wired, not beamed.

Where relay control shines

  • Dedicated cinema rooms where the screen drops as part of a scene — lights dim, projector warms up, screen lowers.
  • Meeting rooms where staff should not need training to find the right remote.
  • Smart home scenes triggered by a wall panel, a time schedule, or a projector’s 12V output.

The catch is wiring. A relay needs a low-voltage cable run from the control point to the screen’s trigger input, usually behind plasterboard or in trunking. If you are refurbishing, that is easy. If the room is finished and the screen is already up, retrofitting a cable can be more disruptive than an IR solution.

IR control: convenient, but line-of-sight dependent

Infrared control is what most electric screens ship with — a handset that beams a signal to a receiver on the screen housing. It is wireless, requires no extra cabling, and works perfectly well in a straightforward living room where the screen is visible from the sofa.

The limitations show up in real homes. Sunlight through a south-facing window can wash out the IR receiver. A low ceiling or a decorative beam can block the beam. And if the screen is hidden behind a valance or inside a ceiling recess, the remote may only work from an awkward angle.

IR in practice

  • Fine for occasional use and rooms where the screen is plainly visible.
  • Less reliable for daily automation or scenes that need the screen to move without someone pointing a remote.
  • IR extenders and blasters can help, but they add another device to power and position.

IR is not obsolete — it is simply a manual convenience rather than an automation backbone. If your idea of smart control is pressing one button on a handset, IR is enough. If you want the screen to be part of a sequence, plan for relay.

App and voice control: the layer on top

App control sounds like the modern answer, and in many setups it is genuinely useful. You can trigger the screen from a phone, include it in a routine, or ask a voice assistant to lower it. But it is worth being clear about what is happening under the bonnet: the app is almost always talking to a relay module or an IR blaster. The screen itself does not have an app.

That means reliability depends on the module and the network, not the screen. A cloud-dependent app can fail when the Wi-Fi drops. A local relay module keeps working. For a room that must work every time — a boardroom, a teaching space, a cinema room — local control is the safer foundation, with app control as a convenience layer.

Relay vs IR vs app: side-by-side

Factor Relay (dry contact) IR remote App / voice
Reliability High — physical connection Moderate — line of sight Depends on network and module
Wiring needed Yes — low-voltage cable to screen No No extra cable, but hub/module needed
Works in bright rooms Yes Can struggle Yes
Scene integration Excellent Limited Good, if local
Best for Fixed cinema and meeting rooms Simple living room setups Convenience and routines

Wiring practicalities before you choose

Before buying any control module, check the screen’s trigger input. Many electric screens use a three-core low-voltage connection for up, down, and common. Some accept a 12V trigger from a projector; others expect a dry contact. The difference matters because a 12V trigger sends voltage, while a dry contact simply closes a circuit. Feeding the wrong signal into the wrong input is a quick way to damage the control board.

Also think about cable route and length. A relay cable run from a cupboard to a ceiling-mounted screen might be 8–12 metres in a typical UK home. Low-voltage cable is slim and can often be tucked into existing trunking, but it still needs planning. If the room is listed or you cannot chase walls, IR or a wireless relay module may be the pragmatic compromise.

A quick pre-purchase checklist

  • Confirm the screen’s control input: dry contact, 12V trigger, or IR only.
  • Decide whether the screen will be part of a scene or used manually.
  • Check the cable route from control point to screen — and whether it can be hidden.
  • If using app control, choose a local module rather than cloud-only where possible.
  • Keep the original IR handset as a backup, even in a relay setup.

Which ABIS screen fits?

For relay-controlled installations, an electric screen is the natural pairing because it is designed to be triggered remotely and hidden away when not in use.

  • 100″ Electric Projector Screen 16:9 — the sweet spot for most UK living rooms and small cinema rooms. A 100″ 16:9 screen sits comfortably in a room where the main sofa is roughly 3–3.5 m back, and the motorised drop makes it easy to integrate with a relay trigger.
  • 120″ Electric Projector Screen 16:9 — better for a dedicated room or a long wall where seating can be pushed back to around 4 m. The larger canvas rewards a relay setup because the screen is often recessed or boxed in, where IR would struggle.
  • 100″ Manual Projector Screen 16:9 — if power or cabling is genuinely difficult, a manual pull-down avoids the control question altogether. It is not automated, but it is dependable and needs no relay or remote.

All three use a matte white 16:9 surface suited to a wide range of projectors. If you are still deciding on size, our guide to ceiling mounts for projector screens covers the installation side in more detail.

Frequently asked questions

Can I use a smart relay with any electric screen?

Only if the screen has a compatible trigger input, usually a dry-contact or low-voltage control terminal. Check the product documentation before buying a relay module. Screens with IR-only control need an IR blaster or a different approach.

Is IR control reliable enough for daily use?

It can be, provided the receiver is visible and not washed out by sunlight. For daily automation or recessed screens, relay control is more dependable because it does not rely on line of sight.

Do I need an app to automate a motorised screen?

No. A relay trigger can be controlled by a wall switch, a projector’s 12V output, or a smart home controller without any app. App control is an optional convenience layer.

What is the difference between a 12V trigger and a dry contact?

A 12V trigger sends a voltage signal to tell the screen to move. A dry contact simply closes a circuit, like a switch. They are not interchangeable unless the screen’s input explicitly supports both.

Can I add relay control to an existing screen?

Sometimes, if the screen has an accessible control terminal and a cable route can be found. Otherwise, an IR blaster or a replacement screen with relay input may be more practical.

Conclusion

If the screen is part of a room’s daily routine, relay control is the quieter, more reliable choice — especially when the screen is recessed or the room is bright. IR still has a place for simple setups where a handset is all you need. App control is useful, but treat it as a layer on top of a solid local trigger rather than the foundation.

Start by measuring the room and confirming the screen’s control input, then choose the size and mounting type that fits. Browse our electric projector screens or manual projector screens to compare options, and contact us if you are unsure which control method suits your space.